The 5th meeting of the 6th National Abrasives Standardization Technical Committee was held in Chongqing

The 5th meeting of the 6th National Abrasives Standardization Technical Committee was held in Chongqing from October 17th to 21st, 2017.

Member and consultant of the National Abrasives Standardization Technical Committee and members of the four sub-technical committees, observers and related representatives of ordinary abrasives, ordinary abrasive tools and silicon carbide special products, super-hard abrasives and products, coated abrasives A total of more than 140 people attended the meeting.

Conference venue

According to the overall work arrangement of this meeting, all delegates' congresses were held on the morning of October 18. Bao Hua, secretary-general of the National Abrasives Standardization Technical Committee, first introduced the leadership on the rostrum, and then explained to the meeting that the chairman Liu Mingyao could not attend the meeting for some reason, and entrusted deputy director Liu Yibo to preside over the meeting. According to the entrustment of Chairman Liu Mingyao, deputy director Liu Yibo presided over the meeting. Deputy Director Liu Yibo first expressed his gratitude to all members and delegates for their serious duties and active participation, and extended their best wishes, and subsequently announced the main agenda of the conference.

Deputy Director Liu Yibo presided over the meeting

According to the agenda of the conference, the Secretary-General of the National Abrasives Standardization Technical Committee, Bao Hua, on behalf of the Secretariat of the Standardization Committee, made a summary of the 2017 work summary of the National Abrasives Standardization Technical Committee and the 2018 work plan, as well as the 2017 National Abrasive Mill. Report on the financial revenue and expenditure of the Standardization Technical Committee. Participants reviewed and approved the two reports.

Secretary Bao Hua’s work report

Then, the conference organized and concentrated on the "Implementation of the "Deepening the Standardization Work Reform Plan" Key Tasks (2017-2018)" (Guo Ban Fa [2017] No. 27), "Thirteenth Five-Year" Technical Standards Science and Technology Innovation Plan (Guo Ke Fa Ji [2017] No. 175) and "Industrial and Communication Industry Mandatory Standards Development Procedures and Requirements (Trial)" (Engineering Letter [2017] No. 653) and other three important documents.

Liu Minqiang, deputy director of the National Abrasives Standardization Technical Committee, presided over the "Implementation of the "Deepening Standardization Work Reform Program" Key Tasks Division (2017-2018)" and "13th Five-Year" Technical Standards Science and Technology Innovation Plan.

Liu Minqiang, deputy director, presided over the study

Secretary Bao Hua presided over the "Procedures and Requirements for Compulsory Standards for Industry and Communication Industry (Trial)". Secretary Bao Hua also conveyed the spirit of attending meetings of the higher authorities on the follow-up of mandatory standards for the machinery industry and the development of group standards.

According to the agenda, Deputy Director Wen Shunru of the Science and Technology Department of China Machinery Industry Federation and Li Jiyun, deputy director of the Industry Work Department of China Machine Tool Industry Association (the two leaders are also the deputy directors of the National Abrasives Standardization Technical Committee) made the meeting. Speak.

Li Jiyun, deputy director

The theme of the speech of Deputy Director Li Jiyun is “Analysis of the economic operation situation of the machine tool industry in 2017”. Director Li first briefly informed the changes and related work of the association, and introduced the work of the association's group standards. Then, Director Li introduced the economic operation of the machine tool industry from January to August. From the statistical data, the machine tool has generally experienced recovery growth in the whole industry. The main business income, total profit and import and export have achieved a large increase, and the “stable and good situation is obvious”. However, there are still four problems in the operation of the industry: first, the demand has been restored, the capacity utilization is not high; second, the low-price competition is fierce and the interests of all parties are harmed; the third is the rising operating costs, and the burden on enterprises is still heavy; The progress is slow and the transition and upgrading is difficult. As for the expectation, Director Li said that our policy environment continued to “stablely and steadily” and the industry operation remained stable; however, as the external environment of industrial development has not changed, the long-term accumulated structural contradictions have not changed, industrial investment, especially technology investment. The growth rate of private investment has not changed, so the industry is still facing downward pressure. Finally, Director Li suggested that the industry should pay attention to national policy measures, especially intelligent, green manufacturing and environmental protection requirements.

Wen Shunru, deputy director

The theme of Wen Shunru’s speech is “to play the basic supporting role of standards in smart manufacturing and green manufacturing”. Director Wen analyzed the basic and strategic position of the machinery industry including the machine tool industry in the entire manufacturing system and the significance of implementing "Made in China 2025", pointing out that strong foundation, intelligence and green are the transformation and upgrading of the industry and achieve sustainable development. The inevitable choice and the only way to develop, and the standardization work has always played an irreplaceable foundation supporting role in actively promoting the process of industrial transformation and upgrading. Director Wen gave affirmation to the standardization work in the field of abrasives. At the same time, it is pointed out that high-speed, high-efficiency, stable, reliable, digital, intelligent, green, integrated, flexible, personalized, etc. is the development direction of the machine tool industry, and it is hoped that the abrasives industry will adapt to this new higher demand. Standardization work must support the technological upgrading of the industry. For the industry standardization work, Director Wen talked about the following points: First, according to the requirements of relevant national departments and the development requirements of the industry, the standards should be for transformation and upgrading, upgrading the technical level and quality, and eliminating backward services; second, strengthening scientific research results. The transformation, further improve the industry's standard level; the third is to adapt to the requirements of intelligent manufacturing; the fourth is to integrate green technology concepts; the fifth is to strengthen the research and development of basic standards; the sixth is to play the role of group standards.

The keynote speeches of the two leaders were detailed, insightful and thought-provoking, which caused a heated discussion among the participants. Deputy Director Liu Yibo made a concluding speech at the conference.

He said that the agenda of the conference is very rich in content. I hope that everyone must carefully understand the spirit and requirements and carry it into the future work. At the same time, he also spoke on behalf of Chairman Liu Mingyao on the following aspects: First, thank the members, consultants and observers for their support of the standardization work in 2017, and thank the standard revision and revision unit for their hard work in the standard revision and revision work. Thanks to everyone's efforts, all the tasks and standard revision projects in 2017 have been successfully completed. Second, the work in the past year has been supported by leaders at all levels. From the State Council to various departments, as well as the China Machinery Industry Federation and the China Machine Tool Industry Association, we attach great importance to the standardization work and have introduced corresponding policies, which is very helpful to our work and effectively ensure the smooth development of our work. Third, we must recognize the gaps in the work, especially the gap between the participation of international standardization and the participation of members. In the future, we must continue to strengthen the effective development of the work of the Standardization Committee as required; the work in 2018 should be fully planned and planned, and the Secretariat and members should further improve and improve the quality of standardization work; it should play a standardized role in the development of the industry.

Deputy Director Liu Yibo concluded the speech

After the conference, the delegates took a group photo.

After the meeting, the sub-technical committees completed the following aspects according to the agenda: (1) reviewed the standard review draft; (2) discussed the 2018 work plan. A total of 16 standard review drafts were reviewed and reviewed, including 6 national standards, namely “General Abrasive Sampling Method”, “Consolidated Abrasives Hardness Test”, “Consolidated Abrasives General Requirements”, and “Super Hard”. Abrasive Cubic Boron Nitride, "Superhard Abrasive Particle Size Inspection" National Standard No. 1 Amendment, "Superhard Abrasive Impact Toughness Determination Method" National Standard No. 1 Amendment; Industry Standard 10 items, respectively, "Ordinary Abrasive Zirconium Corundum, "Chemical Analysis Method of Silicon Carbide Deoxidizer", "Consolidated Abrasive Milling Wheel", "Superhard Abrasive Polycrystalline (Polycrystalline) Diamond or Cubic Boron Nitride Composite Sheet Variety, Size", "Super Hard Abrasive" Drilling tools with triangular diamond polycrystals, "Superhard abrasive products diamond dressing pen", "Superhard abrasive products for diamond processing stone processing", "Coated abrasive steel paper sanding disc technical conditions", "Coated abrasives" Sandpaper, "Technical Conditions for Coated Abrasive Tube Sand Cover". (3) Focused on the 2018 proposed revision and revision standard project planned in the “13th Five-Year” technical standard system construction plan, and also reviewed the newly proposed standard project proposal.

The meeting completed the scheduled agenda and achieved a complete success.

Solar Stair Light

Quality You Can Trust
The solar lights a seamless combination of 304 stainless steel and high-impact ABS plastic which will not rust for years, it is durable for year round use outside.

Charge Faster & Work Longer
outdoor solar stair lights can absorb more power from the sun for about 6-8 hours. The rechargeable battery work much longer than other outdoor wireless solar lights in the market, which can let the LED solar lights illuminate about 8-10 hours on a full charge.
Charge Automatically
Press the On/Off button, turn the outdoor solar lights on (Auto mode), let the solar fence lights charged in the unlimited and free sun. It will automatically turn on at dusk or with the onset of inclement weather and off at dawn. Each solar outdoor light has 3 premium quality LEDs, which can give out a visible bright light on your path.
IP44 Wet Rated & Durable
The outdoor step lighting is made of stainless steel and high quality lamp shell, can be used in rainy or wet condition. The operating temperature range is 14℉ to 122℉, suitable for step, fence, outdoor stairs, garden, deck and etc.
Easy to Install
Fast and easy installation, no wiring required, simply screw it onto the surface (Screws included). This outdoor solar LED light can be quickly installed in any place where it can absorb the sun light directly. Used for road, path, deck, dock, stair, fence, wall, garden, walkway, sidewalk, backyard etc.

Solar Stair Light,LED Solar Step Lights,,RGBW Solar Stair Lights, Newest Solar Fence Light LED Solar Manafacuture

Shenzhen You&My Electronic Technology Co., Ltd , https://www.youmyledlight.com