3D Water Steam Fireplace,3D Water Fireplace,Small Water Steam Fireplace,Water Steam Fireplace Without Heat JINAN LODOR CNC EQUIPMENT CO.,LTD , https://www.zgfireplace.com
Steps for starting the gasoline generator
About 30kw Gasoline Generator Startup Procedure
Gasoline generator use introduction
Preparation and inspection before use
1. Unpacking check: After the unpacking, check the appearance of the machine for bump damage. Inventory all accessories.
2. Install two directional castors and two steering castors.
3, fuel capacity indicator
Note: Unleaded gasoline above 90# must be used. Specific operations are as follows: remove the fuel tank cap (counterclockwise rotation), add fuel, and always observe the tank on the capacity of the logo, should not be too full to prevent fuel spillage. Do not remove the fuel filter when refueling.
4ã€Oil ( 30kw petrol generator needs about 4 liters of oil)
The generator is not filled with oil at the factory and must be filled with oil before use. Otherwise it will cause permanent damage to the engine.
(1) Oil filling port. For the oil quality standard, please use the SJ or SG or higher grade gasoline engine oil of type 15W-30 (in the cold regions, the model number should be 5W-30).
(2) Engine oil level: Pull out the oil gauge and check the oil level. It should be between the upper limit and the lower limit. It is better to approach the upper limit, but it cannot exceed the limit.
(3) If the engine oil is excessive, the generator set cannot work normally. Please drain the excess oil through the oil drain.
5, start the battery: (optional 12V ~ 36Ah capacity above)
(1) Connect the red end to the positive pole of the starter battery, the black end to the negative pole of the starter battery, and tighten the terminal screws to make good contact.
(2) Be careful not to short-circuit the battery due to the tool used when connecting the battery cable.
(3) It is forbidden to invert the positive and negative poles of the battery cable and positive and negative poles of the battery, otherwise the starter motor will be damaged.
Third, the operation of the generator set
Before starting the 30kW gasoline generator , be sure to set the output AC switch to the [OFF] position (switch down). Otherwise it will damage the generator. It is prohibited to start with direct load.
1, 30kw gasoline generator start
(1) Open the fuel valve in the ON position, ie the oil circuit switch is in the vertical position
(2) Rotate the start switch to the RUN position and rotate the start switch to the START position. If the startup is successful, remove the hand immediately and allow it to automatically turn to RUN. If the startup is unsuccessful, restart after 10 seconds and start successfully. (Note: Each start-up time must not exceed ten seconds).
Gasoline generator set introduction
Pre-use preparation and inspection 1. Unpacking inspection:
After unpacking, check the appearance of the machine for bump damage. Inventory all accessories.
Caster installation:
2. Install two directional castors and two steering castors.
3, fuel capacity indicator
Note: Unleaded gasoline above 90# must be used. Specific operations are as follows: remove the fuel tank cap (counterclockwise rotation), add fuel, and observe the tank at any time on the capacity logo,
Should not be too full to prevent fuel spillage. Do not remove the fuel filter when refueling.
4ã€Oil (This generator needs about 4 liters of oil
The generator is not filled with oil at the factory and must be filled with oil before use. Otherwise it will cause permanent damage to the engine.
(1) Oil filling port. For the oil quality standard, please use the SJ or SG or higher grade gasoline engine oil of type 15W-30 (in the cold regions, the model number should be 5W-30).
(2) Engine oil level: Pull out the oil gauge and check the oil level. It should be between the upper limit and the lower limit. It is better to approach the upper limit, but it cannot exceed the limit.
(3) If the engine oil is excessive, the generator set cannot work normally. Please drain the excess oil through the oil drain.
5, start the battery: (optional 12V ~ 36Ah capacity above)
(1) Connect the red end to the positive pole of the starter battery, the black end to the negative pole of the starter battery, and tighten the terminal screws to make good contact.
(2) Be careful not to short-circuit the battery due to the tool used when connecting the battery cable.
(3) It is forbidden to invert the positive and negative poles of the battery cable and positive and negative poles of the battery, otherwise the starter motor will be damaged.
Third, the operation of the generator set
Before starting the generator set, be sure to set the output AC switch to the [OFF] position (switch down). Otherwise it will damage the generator. It is prohibited to start with direct load.
1, the start of the generator set
(1) Open the fuel valve in the ON position, ie the oil switch is in the vertical position, and gently pull out the damper with your fingers.
3) Rotate the start switch to the RUN position and rotate the start switch to the START position. If the startup is successful, remove the hand immediately and allow it to automatically turn to RUN. If the startup is unsuccessful, restart after 10 seconds and start successfully. (Note: Each start-up time must not exceed ten seconds).