Air compressor is one of the main mechanical power equipments of many enterprises. It is very necessary to keep the air compressor safe. Strict implementation of the air compressor operating procedures not only helps to extend the service life of the air compressor, but also ensures the safety of the air compressor operator. Let us understand the air compressor operating procedures. First, before the operation of the air compressor, you should pay attention to the following issues: 1. Keep the oil in the oil pool within the scale. Before the air compressor is operated, check that the oil in the oiler should not be lower than the mark value. 2. Check whether the moving parts are flexible, whether the joint parts are tight, whether the lubrication system is normal, and whether the motor and electrical control equipment are safe and reliable. 3. Check whether the protective device and safety accessories are intact before the air compressor is operated. 4. Check that the exhaust line is clear. 5. Turn on the water source and open each inlet valve to make the cooling water unblocked. Second, the air compressor operation should pay attention to the long-term deactivation after the first start, must be checked by the car, pay attention to whether there is impact, stuck or abnormal sound. Third, the machine must be started under no load condition. After the no-load operation is normal, the air compressor is gradually put into the load operation. 4. When the air compressor is in operation, after normal operation, always pay attention to various meter readings and adjust them at any time. 5. In the operation of the air compressor, the following conditions should also be checked: 1. Whether the motor temperature is normal and whether the meter reading is within the specified range. 2. Whether the running sound of each machine is normal. 3. Whether the suction valve cover is hot or not, and the sound of the valve is normal. 4. Whether the various safety protection devices of the air compressor are reliable. 6. After the air compressor is operated for 2 hours, the oil and water in the oil-water separator, the intercooler and the after-cooler should be discharged once, and the oil and water in the storage tank should be discharged once per shift. 7. When the following conditions are found during the operation of the air compressor, stop immediately, find out the cause, and eliminate it. 1. The lubricating oil is terminated or the cooling water is terminated. 2. The water temperature suddenly rises or falls. 3. The exhaust pressure suddenly rises and the safety valve fails. 4. The load suddenly exceeds the normal value. 5. The mechanical noise is abnormal. 6. An abnormality has occurred in the motor or electrical equipment. 8. After the air compressor is operated, close the cooling water inlet valve after stopping. Nine, if the power supply is stopped, the motor should be restored to the starting position to prevent the power supply from being restored, resulting in an accident due to the inactivation of the starting controller. 10. The operation of the motor part of the air compressor shall be carried out in accordance with the relevant provisions of the motor. XI. The operating part of the air compressor must be implemented in accordance with the relevant provisions of the internal combustion engine. 12. When the air compressor is operated for more than 10 days, it should be injected with sufficient lubricating oil to each friction surface. When parking for more than one month for long-term storage, in addition to releasing all kinds of oil and water, removing all inlet and exhaust valves and blowing them clean, the cylinder mirror surface, piston top surface, crankshaft surface and all non-mating surfaces should be cleaned and oil-sealed. Cover the oil seal with a cover to prevent moisture and dust from entering. 13. The mobile air compressor should carefully check whether the running device is intact and tight before each towing. The towing speed is generally not more than 20 km / hour. 14. When the air compressor is operated, the safety accessories such as the air storage cylinder, safety valve and pressure gauge must meet the requirements of the safety technology of the compressed air storage cylinder of the Ministry of Railways. 15. The air filter of the air compressor must be cleaned frequently and kept open to reduce unnecessary power loss. 16. When the air compressor is operated with large dust such as sandblasting and rust removal, the machinery should be kept at a certain distance from the sandblasting site, and corresponding dustproof measures should be taken. Liquid Polishing Wax ,Buffing Metal Wax,,Mirror Polishing Solution,Green Liquid Polishing Wax NINGBO HENGHUA METAL SURFACE TREATMENT TECHNOLOGY CO.,LTD. , https://www.henghuametal.com