The glass door film is a kind of PET functional film that is attached to the glass surface. The places where we see glass doors in our daily life basically have this layer of film. As a new type of energy-saving building materials, glass film has several advantages such as heat insulation, heat preservation, safety explosion-proof, anti-ultraviolet radiation, anti-glare glare, easy to create private space, enhance visual effects, high temperature and fire resistance. So, what about the glass door sticker ? Next, we will learn how to apply the glass door film , I believe it will help you. Glass Door Films - Method Tips 1, familiar with the tool, a good size â— Construction points : check the tool is not missing, the size of the same side of the window; The tools we prepared before filming should include at least four scrapers, a watering can, a utility knife, and a ruler, and carefully check whether the tool is smooth, smooth, and notched; after that, we measure the length and width of the window, and measure the size of the window. Must start on the same side of the window. 2, cut the film â— Construction points : The soft cloth is placed on the pad, the film edge is aligned with the center line, and the size is 5-8mm smaller than the glass; Take out the film to check the size and quantity of the film, and then put a small blanket or soft cloth on it to avoid scratching the floor. When cutting, align the film edge to the center line and cut it out. The cut size is 5-8mm smaller than the glass size. Behind the membrane. 3, cleaning glass â— Construction points : spray several times more than water, clean, no dust, no dust, no sand; The glass must be cleaned, this is very important for the effect of the film, wash the glass thoroughly. Spray more water, scrape with a film and scrape several times, so that the glass is free of dust and dust, no sand, after cleaning the glass and spray a layer of water. 4, on the film â— Construction points : Spray the lubricant to reduce the viscosity of the adhesive layer, first hit the cross, and then scrape the film on both sides; The film is divided into two layers, one layer is a colorless and transparent film called protective film, and the other layer is called adhesive film with a color tape. First, spray the lubricating fluid on the upper film to reduce the adhesiveness of the adhesive layer. Then, remove the protective film while applying the film. Adjust the position of the film on the glass window. The action is to first hit the cross, then scrape the film from the middle to both sides to fix the film. Bubbles are driven out from both sides. Use less force to avoid scratching the film. 5, scraping film to catch water â— construction points : small towel absorbent, trim corner, dry wipe; Spraying lubricant on the film, separating the protective film from the film. The direction of action is the same as in the previous step. The water is vigorously blown away, and the water that has been scraped out is wiped with a small towel. Finally, the corners that have not been shaved are trimmed and removed. Protective film, film finish. When all windows are filmed, spray a small amount of detergent to remove other residues. Wipe it with a dry rag to make the window smooth and bright. Glass Door Films - Precautions 1, when cutting the film should be slightly larger than the glass 1cm or more. 2, the protective film is affixed to the middle to a cross buckle positioning, first middle and back sides of the principle of wipe the water, so that the film does not bubble. 3. Whether the edge of the wiper blade is even and smooth and there is a gap, be sure to carefully check the tool. 4. When the glass door film is finished, spray a small amount of detergent to remove other residues. Wipe it with a dry rag to make the glass smooth and bright. Glass Door Film - Maintenance and Care 1. Do not move the glass within 3 days after the window film is installed. 2. Within 15 days after installation of the window film, do not wipe the glass with water. 3. Do not use a sucker to hang or glue any items on the glass, and do not paste stickers on the window film. 4. Lightly and evenly spray the surface of the window film with an ammonia-free cleaning agent, and then gently wipe the glass with a clean, soft cotton cloth or a soft paper towel. The cotton cloth and paper towels often need to be wrung out and contained on the cotton cloth/paper towel. Pure rubbing alcohol will quickly dissolve huge stains and fatty fingerprints. If the stain is not washed, re-spray the cleaning solution and wipe the window film horizontally from top to bottom with a soft rubber wiper wipe until dry. Dry the edge of the glass with a towel. 5. When adhesive tapes, sticky notes or decals are used on the window film, the remaining glue or viscose when removing these materials can be softly wiped with acetone (nail polish remover) In the contaminated area, the viscose that remains on the glass film can be quickly and completely removed. A small amount of acetone will not damage the film of the vinegar, but it can immediately dissolve and completely evaporate the viscose and most of the paint. 6. Do not use a hard eraser, brush, or sand-containing wipe to clean the glass film. The above is how the glass door and glass door mask affixed methods and techniques of film-related content, if you are also in need, may wish to try it! If you want to learn more about this, please pay attention to this website information channel. Glass door
Baking rack,baking cooling mesh,Baking cooling rack,Cooling Rack, steel wire cooling rack, etc.
Baking wire mesh is made of high quality 304 stainless steel, never rusting and durable. Cooling Wire mesh does not have any coating or chemical ingredients, making food safer.
2 tier Cooling Rack,3 tier Cooling Rack,Foldable Cooling Rack,Creative Cooling Rack Shenzhen Lanejoy Technology Co.,LTD , https://www.injectionnut.com
