Explore our large inventory of Komatsu final drives and Komatsu travel motors. Talk to a parts expert and find a best-priced, best-built Final Drive.
Komatsu Final Drive,Komatsu Final Drive Assy,Komatsu Travel Motor,Komatsu Travel Gearbox,Komatsu Final Drive Spare Parts,Komatsu Drive Parts,Komatsu Motor Jining Juheng Hydraulic Machinery Co., Ltd. , https://www.juheng-cn.com
Unfortunately, it may sometimes be that case that your Komatsu machine will no longer move and you can therefore not continue working. The reason for this can be a worn final drive. You, of course, want your machine to start working again as soon as possible. The final drive must therefore be replaced as soon as possible.
With solutions available for over 70 Komatsu excavator models, we are sure to have the Komatsu final drive or Travel Motor you need. Our new JUHENG brand final drives and reconditioned OEM final drives are both excellent options that provide incredible performance and reliability at up to 70% off the cost of new OEM dealer pricing and yet still offer the peace-of-mind of that comes from purchasing a final drive from a respectable, long-standing final drive provider.
At JUHENG, our confidence in our products allows us to offer a 2-year warranty on new JUHENG Brand final drives and 6 month warranty on reconditioned final drives.
Komatsu Final Drive,Komatsu Final Drive Assy,Komatsu Travel Motor,Komatsu Travel Gearbox,Komatsu Final Drive Spare Parts,Komatsu Drive Parts,Komatsu Motor.
With solutions available for over 170 Komatsu excavator models, we are sure to have the Komatsu final drive or travel motor you need.long-standing final drive provider.and 15 month warranty on final drives.
H-150 slide valve vacuum pump overview
Sliding valve mechanical vacuum pump, is to remove the general gas or a small amount of condensable steam gas vacuum equipment, used in vacuum smelting, vacuum drying, vacuum impregnation and other vacuum operations. It can be used alone, but also as a fore pump for other high vacuum pumps, but not for pumping from one container to another as a transfer pump. When pumping high oxygen content, explosive, corrosive ferrous metals, the vacuum pump oil chemical reaction, water, dust and other gases, additional devices should be attached. H-150 Spray Valve Vacuum Pump Applications: Widely used in aerospace, aviation, atomic, petroleum, chemical, pharmaceutical, electrical, ceramics, smelting, new materials, vacuum heat treatment, vacuum coating and other industries. H-150Stroke valve vacuum pump Structure Description: 1 Structure: H-150B-type slide valve vacuum pump guide hole and the center of the pump connection at a horizontal angle of 30 °, the horizontal structure, the motor has two kinds of bypass and overhead, Landing area can be smaller. In order to facilitate debugging and troubleshooting identification, the fuel tank has a side cover, exhaust port located on the side cover. The pump to improve the anti-injection ability of high inlet pressure operation can be improved to reduce fuel consumption and environmental pollution. 2 suction principle: The pump pump body 1, guide rail 2, slide valve 3, eccentric 4, shaft, two pump cover 5, and the exhaust valve 6 constitute the pump suction chamber and exhaust chamber. When the shaft rotates counterclockwise, the eccentric wheel drives the slide valve to operate up and down, left and right. As the suction chamber gradually expands, gas is sucked into the pump chamber through the spool through the pump inlet. At this point, the exhaust chamber is gradually reduced, the compressed gas and oil will eventually push the exhaust valve into the tank, and then into the next cycle, to achieve the exhaust effect. The pump with gas ballast valve 7, when you open the gas ballast valve, gas can be mixed into the exhaust chamber of the pump to reduce the period of steam partial pressure, you can remove a certain amount of water vapor and purify the pump oil, extend the pump oil The use of time, improve lubrication conditions, increase pump reliability. 3 oil: oil from the tank through the oil into the oil pump, and then from the pump into the oil box, dispensed to the pump chamber at both ends, the slide valve and guide rail, eccentric friction parts, from the exhaust valve back to the tank. 4-end shaft seal between the oil pipe and the tank connected: Bearings can be used in the -40 ° C- +200 ° C range of high-temperature grease lubrication, requiring 5000 hours of operation change. The loading is one-third or one-half of the bearing clearance.