Common failures of electrical equipment in machining centers are classified into common failures of electrical equipment in machining centers according to the characteristics, phenomena, causes or adverse effects of common failures.
1. Description of M mddium duty slurry pump
Naipu NP-M series centrifugal slurry pumps and spare
parts could fully interchange with world famous brand.These pumps are of
heavy-duty construction, designed for continuous pumping of highly
abrasive and corrosive slurries. They feature a wide choice of
replaceable abrasion resistant metal casting liners and Impellers, which
are all interchangeable within a common casting assembly.
Dewatering
2.Construction drawing of M medium duty slurry pump
Main Part Number At The Drawing
032:Frame Plate
132:Discharge Joint
Material of Construction
LINERS
IMPELLERS
CASING
BASE
EXPELLER
EXPELLER RING
SHAFT SLEEVE
SEALS
Standard
Chrome Alloy
Chrome Alloy
SG Iron
SG Iron
Chrome Alloy
Chrome Alloy
SG Iron
Rubber
3.M Medium duty slurry pump select Chart
1. According to the location of common faults, it is divided into common hardware configuration faults and mobile phone software common faults. Hardware configuration common faults refer to abnormal conditions and even destruction of electronic devices, household appliances, pcb circuit boards, cables and wires, connectors, etc. It is Common faults that must be repaired or even removed and replaced. The common faults of mobile phone software generally refer to the common faults caused by the PLC logic management program. You must type or change some data information or even change the PLC program flow to clear the common faults. Common faults in the parts processing program flow are also classified as common faults in mobile phone software. The most serious common fault of mobile phone software is the damage or even loss of mobile phone software of CNC machine tools. This can only be dealt with by the manufacturer or its service project organization. 
2. According to whether there are common faults or not, they are divided into common faults with diagnosed signs and common faults without diagnosed signs. Today's CNC lathes and CNC machine tools are designed with the ultimate self-diagnostic program flow. 1. Hardware configuration features. Once a common fault is found, it will immediately alert or a brief text description will be displayed on the screen. The diagnosis guide of the fusion system software configuration can not only find the cause and location of the common fault, but also have a way to clear it. CNC lathe makers will also have related common fault signs and diagnosis instructions for the actual CNC lathe design. The above two parts of common faults with diagnosed signs and various display lights on various electrical equipments facilitate the removal of common faults of most electrical equipments. A part of the common faults without the diagnosis sign is caused by the inconsistency of the procedures of the two kinds of diagnosis procedures (such as the power switch is not closed and the connection of the lamp is loose, etc.). Such common faults must be analyzed and cleared with the help of the maintenance staff's understanding of the CNC lathe and the technical strength of the entire process and common fault conditions and adverse effects of the work before causing the common fault.
3. According to whether the common faults are destructive, they are divided into devastating common faults and non-destructive common faults. For common faults such as devastating common faults, damaged steel parts and even CNC lathes, it is not allowed to repeat the same mistakes during maintenance. Relatively check and analyze the status of common faults to eliminate them. The technical level is high and there is a certain degree of risk. If the steel parts will be destroyed, you can remove the steel parts and try to reproduce the entire process of common failures, but you should be very careful.
4. Based on the probabilities of common failures, it is divided into targeted common failures and accidental common failures. Targeted common failures refer to the clear common failures that will be caused if certain standards are considered; and accidental common failures refer to Common failures that sometimes occur under the same standards. The analysis of such common failures is more difficult. Generally, it is often loosely displaced from the CNC lathe mechanical system, part of the electrical equipment steel features drift or credibility is reduced, electrical equipment The internal temperature is too high. The analysis of such common faults will only be cleared after continuous experiment and comprehensive discrimination.
5. Considering the fitness characteristics of the CNC lathe, it is a common failure of the fitness characteristics of the CNC lathe. Under such circumstances, although the CNC lathe can run normally, it can produce and process steel parts that do not meet the standards. For example, the accuracy grade deviation of CNC lathes, the dead zone in the opposite direction is too large, and the coordinate operation is unstable. Such common faults must be diagnosed by the testing equipment to diagnose the mechanical and electrical phases that caused the deviation, and then removed according to the optimal adjustment of the gear transmission system software, CNC machine tool and servo control system.
http: //
================================================== ================================================== ====== 
Typical Applications---
Dense media transfer
Dense media make-up
Bottom boiler and fly ash
Ferrosilicon make up
Thickener underflow
110:Volute Liner
041:Frame Plate Liner Insert
124: Volute Cover Seal
122: Stuffing Box Seal
147:Impeller
013:Cover Plate
083:Throat bush
060: Intake Joint
or
SG Iron
or
SG Iron
M Medium Duty Slurry Pump,Heavy Duty Slurry Pump,Warman Slurry Pump,Medium Duty Slurry Pump
Shijiazhuang Naipu Pump Co., Ltd. , https://www.naipu-pump.com