Decoration company entrance decoration faucet switch socket Why are all the scenic spots using space capsules house? Capsule House, Space capsule,Eco Capsule Houses,space capsule for sale Henan Jinming Metal Material Co., Ltd. , https://www.hnjmmetal.com
[Precautions for bathroom renovation process]
Do not damage the waterproof layer. If there is damage or no waterproof layer, waterproof should be done first, and 12 hours of water leakage test.
Sanitary ware is firmly fixed and the pipe connections are tight.
Pay attention to finished product protection and prevent bumping sanitary ware.
Sanitaryware must be selected in advance, do not wait until the late decoration. This will produce unexpected troubles.
ã€The toilet installation process】
Check the ground drain pipe → align the nozzle → flatten the alignment → draw the mark → punch the hole → put the putty → cover the rubber pad → screw on the nut, → mark the two holes on the back of the tank → punch → Insert the bolt → Securely press → Place the back tank with the flat alignment → Screw on the nut → Install the backwater tank elbow → Install the eight-word door → Bend the fork of the maternity lamp → Insert the drift door and the eight-character door → Tighten the nut.
ã€The installation of toilets】
1) The height of the water supply pipe is usually 250mm from the ground to the center of the valve. If the one-piece toilet is installed, the height of the water inlet of the toilet shall be determined, but not less than 100mm. The center of the water supply valve is generally in the sewer pipe. 150mm to the left of the center or position based on the actual size of the toilet.
2) The low tank toilet uses galvanized bolts or galvanized metal expansion bolts in the tank. If the wall is a perforated brick, expansion bolts are strictly prohibited. A soft gasket should be used between the tank and the nut. It is forbidden to use a metal hard plate.
3) The water tank should be no more than 20mm away from the wall of the water tank and one-piece toilet.
4) The installation of the toilet shall not be less than 6mm galvanized expansion bolts, the soft washer shall be used between the toilet and the nuts, and the sewage pipe shall be exposed to the ground 10mm.
5) When the toilet is installed, put the putty around the bottom drain first, then slowly align the discharge outlet of the toilet with the sewage pipe and press it down to fill the flat surface. Then tighten the gasket nut and remove it. Putty, with a putty filling around the base immediately after cleaning with a wire or wipe.
6) The height of the overflow pipe in the flushing tank should be 30~40mm lower than the wrench hole to prevent water overflow from the wrench hole when the inlet valve is damaged.
[bath installation process]
Expansion bolts are inserted → æ» â†’ → → 盆 盆 盆 盆 盆 盆 挂 挂 挂 把 把 把 把 把 把 把 把 把 把 脸 脸 把 把 把 把 把 把 把 把 把 。 。 。 。 。 。 。 →
[basin installation construction essentials]
(1) Sink basin products should be flat and lossless. Drain plugs shall have overflow holes of not less than 8mm diameter.
(2) Drain plugs and sinks When connecting, the drain plug overflow hole should be aligned with the overflow hole of the sink basin as much as possible to ensure that the overflow site is unblocked. The top surface of the drain plug should be lower than the bottom of the wash basin after being attached.
(3) Bracket fixing bolts may be galvanized bolts or galvanized metal expansion bolts of not less than 6mm (if the wall is perforated, expansion bolts are strictly prohibited).
(4) After connecting the sink with the drain pipe, it should be solid and dense, and it is easy to disassemble. The joint must not be exposed. The sinks are applied with silicone paste at the wall contact points.
[bath installation process]
Expansion bolts are inserted → æ» â†’ → → 盆 盆 盆 盆 盆 盆 挂 挂 挂 把 把 把 把 把 把 把 把 把 把 脸 脸 把 把 把 把 把 把 把 把 把 。 。 。 。 。 。 。 →
[basin installation construction essentials]
(1) Wash basin products should be smooth and lossless. Drain plugs shall have overflow holes of not less than 8mm diameter.
(2) Drain plugs and sinks When connecting, the drain plug overflow hole should be aligned with the overflow hole of the sink basin as much as possible to ensure that the overflow site is unblocked. The top surface of the drain plug should be lower than the bottom of the wash basin after being attached.
(3) Bracket fixing bolts may be galvanized bolts or galvanized metal expansion bolts of not less than 6mm (if the wall is perforated, expansion bolts are strictly prohibited).
(4) After connecting the sink with the drain pipe, it should be solid and dense, and it is easy to disassemble. The joint must not be exposed. The sinks are applied with silicone paste at the wall contact points.
(5) If sink drainage traps and taps are plated products, the coating must not be damaged during installation.
(5) If sink drainage traps and taps are plated products, the coating must not be damaged during installation.
[Shower installation process]
Cold and hot water nozzles are leveled with test tubes → Measure short section dimensions → Installed on the nozzles → Apply brass to the water inlet of the shower and apply the nut → Tighten on the wall → The upper copper tube is installed in the three ports → Wood screws are fixed to the wall.
[Bidet installation process]
Hybrid switch, hot and cold water door cover and nut leveling, → water gate installed → nozzle turn core door installed → hot and cold water door outlet nut tightening → hybrid switch nut tightening → install three water door cover → magnetic bowl installation Good → When installing the nozzle → Install the drain → When installing the handlebar → Adjust the positioning.
The tourism industry is developing very fast, and the same attractions have no characteristics, and it is also difficult to attract consumers. In fact, many scenic spots have begun to use space capsules. This kind of architectural design is unique, and the price is very favorable, and the construction efficiency is high. It can be constructed according to our needs immediately. So what are the advantages of such a building? Why are attractions in use?
removable design
Space capsules house are generally made of steel, etc., and do not need to lay foundations, do not require land approval, can ensure that the construction is pollution-free, and the construction efficiency is also guaranteed. Moreover, it is generally possible to carry out mobile design directly, so that only need to design and construct according to the needs, the use of the building is also guaranteed, and it is very convenient to move and use at any time.
Internet celebrity building
Because the design style of this kind of building is unique, it is completely different from ordinary prefabricated houses, and it can also be painted and designed on the surface. Basically, after the construction of this kind of building is completed, it will immediately become a landmark building of the scenic spot, and it has a cosmic atmosphere, so everyone still likes it very much. Distinctive design is also important if you want to attract tourists.
long lasting
The construction of the space capsule house is simple, and its service life is relatively long, because it is made of light steel structure, the wall panels are made of aluminum alloy panels, and three layers of insulating glass, so as long as you can buy high-quality materials, then its use The lifespan can reach more than several decades. Its material has strong corrosion resistance, and is windproof, fireproof, etc., and its practicality is also very guaranteed. Buildings with high safety factors and favorable prices are also worth choosing.
discount price
Because each scenic spot may have a time limit for decoration, it is also necessary to pay attention to the budget. The construction of the space capsule is very simple, and the design can be completed according to the needs, and its construction cost is also very favorable. Moreover, it can be constructed quickly, put into use immediately, and will not generate any construction waste, etc. The cost-effective building is also very suitable for various scenic spots.
Bathroom renovation process
Wall tiles, ceilings, floor tiles, toilets, washbasins and bathtubs, installation and connection of drains, installation of lamps, sockets, mirrors, installation of towel bars and other hardware accessories.